Lemon Law Center

Home > Oldsmobile

2004 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

on certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a passenger using the interior handle to open the power sliding door could be injured.

Corrective Action

if a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

Recall Notes

dealers will replace the power sliding door interior handle on the passenger-side. if the vehicle is equipped with a power or manual sliding door on the driver-side, the interior handle will also be replaced for appearance reasons. note: before the vehicle is serviced, gm advises owners to not use the interior door handle to open the door. the driver can open and close the door from switches at the driver's position or by using the remote key fob. the driver should tell passengers to use the switch located in front of the door to open or close it. the driver should use the override switch to prevent operation of the power door by children or by others who are not familiar with its use. the owner notification letter mailing will be conducted in phases with the first phase beginning on may 31, 2005. the second phase mailing began on july 18, 2005. the recall began on may 31, 2005. phase 2 began on july 18, 2005. phase 3 (final phase) began on august 24, 2005, to all remaining customers. owners should contact chevrolet at 1-800-630-2438; pontiac at 1-800-620-7668; or oldsmobile at 1-800-630-6537.

2004 Oldsmobile Silhouette

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.

2003 Oldsmobile Silhouette

Component

Air Bags:Frontal

Consequence of Defect

certain passenger, mini vans, and sport utility vehicles have an air bag inflator on the driver's side that could fracture at a weld during a deployment.

Corrective Action

pieces of the inflator could strike and injure vehicle occupants and the air bag cushion would not inflate fully, reducing the capability of the bag to protect the driver.

Recall Notes

dealers will inspect, and replace, if necessary, the air bag module assembly on the driver's side. owner notification began august 15, 2002. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact buick at 1-800-521-7300, cadillac at 1-800-458-8006, chevrolet at 1-800-222-1020, gmc at 1-800-462-8782, oldsmobile at 1-800-442-6537, or pontiac at 1-800-762-2737.

2003 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

on certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a passenger using the interior handle to open the power sliding door could be injured.

Corrective Action

if a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

Recall Notes

dealers will replace the power sliding door interior handle on the passenger-side. if the vehicle is equipped with a power or manual sliding door on the driver-side, the interior handle will also be replaced for appearance reasons. note: before the vehicle is serviced, gm advises owners to not use the interior door handle to open the door. the driver can open and close the door from switches at the driver's position or by using the remote key fob. the driver should tell passengers to use the switch located in front of the door to open or close it. the driver should use the override switch to prevent operation of the power door by children or by others who are not familiar with its use. the owner notification letter mailing will be conducted in phases with the first phase beginning on may 31, 2005. the second phase mailing began on july 18, 2005. the recall began on may 31, 2005. phase 2 began on july 18, 2005. phase 3 (final phase) began on august 24, 2005, to all remaining customers. owners should contact chevrolet at 1-800-630-2438; pontiac at 1-800-620-7668; or oldsmobile at 1-800-630-6537.

2003 Oldsmobile Silhouette

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.

2002 Oldsmobile Silhouette

Component

Air Bags:Frontal

Consequence of Defect

certain passenger, mini vans, and sport utility vehicles have an air bag inflator on the driver's side that could fracture at a weld during a deployment.

Corrective Action

pieces of the inflator could strike and injure vehicle occupants and the air bag cushion would not inflate fully, reducing the capability of the bag to protect the driver.

Recall Notes

dealers will inspect, and replace, if necessary, the air bag module assembly on the driver's side. owner notification began august 15, 2002. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact buick at 1-800-521-7300, cadillac at 1-800-458-8006, chevrolet at 1-800-222-1020, gmc at 1-800-462-8782, oldsmobile at 1-800-442-6537, or pontiac at 1-800-762-2737.

2002 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

on certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a passenger using the interior handle to open the power sliding door could be injured.

Corrective Action

if a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

Recall Notes

dealers will replace the power sliding door interior handle on the passenger-side. if the vehicle is equipped with a power or manual sliding door on the driver-side, the interior handle will also be replaced for appearance reasons. note: before the vehicle is serviced, gm advises owners to not use the interior door handle to open the door. the driver can open and close the door from switches at the driver's position or by using the remote key fob. the driver should tell passengers to use the switch located in front of the door to open or close it. the driver should use the override switch to prevent operation of the power door by children or by others who are not familiar with its use. the owner notification letter mailing will be conducted in phases with the first phase beginning on may 31, 2005. the second phase mailing began on july 18, 2005. the recall began on may 31, 2005. phase 2 began on july 18, 2005. phase 3 (final phase) began on august 24, 2005, to all remaining customers. owners should contact chevrolet at 1-800-630-2438; pontiac at 1-800-620-7668; or oldsmobile at 1-800-630-6537.

2002 Oldsmobile Silhouette

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.

2001 Oldsmobile Silhouette

Component

Air Bags:Frontal

Consequence of Defect

on certain passenger, sport utility vehicles and mini vans, some of these vehicles have a passenger air bag that was manufactured without a check valve pin. an air bag without the check valve pin could produce increased pressure at the onset of the air bag deployment and reduced pressure afterward.

Corrective Action

this could increase the severity of injury to a person who was not properly restrained and who was close to the passenger air bag at the time of deployment. it could also reduce the ab8ility of the air bag to protect a restrained front seat passenger.

Recall Notes

dealers will inspect and, if necessary, replace the passenger air bag. owner notification began december 16, 2002. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, oldsmobile at 1-800-442-6537, or saturn at 1-800-553-6000, prompt #3.

2001 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: 1997-2001 chevrolet venture, pontiac montana/transport, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors that were serviced in campaign 01013 (01v-067) from april to august 2001. also 2001 chevrolet venture, pontiac montana, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors assembled in january through april 2001. these vehicles have inadequate front welds. if a front weld fails, the actuator can jam in the unlatched position and, when the sliding door closes, it will not be latched.

Corrective Action

if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface. an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will inspect and, if required, install a new power sliding door unlatch actuator assembly. owner notification began on october 22, 2001. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

2001 Oldsmobile Silhouette

Component

Seats:Front Assembly:Recliner

Consequence of Defect

vehicle description: certain mini vans built with second row 50/50 split bench seats or captain's chairs, fail to comply with the requirements of fmvss no. 225, "child restraint anchorage systems." the seat latch anchor wire diameter is greater than 6.1 mm.

Corrective Action

if the connector for a latch-type child restraint is not attached correctly to the anchorage points, the restraint will not properly protect a child in the event of a crash.

Recall Notes

dealers will inspect the latch anchor wires and repair those with an improper diameter. owner notification began april 10, 2002. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, oldsmobile at 1-800-442-6537, or pontiac at 1-800-762-2737.

2001 Oldsmobile Silhouette

Component

Seat Belts

Consequence of Defect

vehicle description: passenger vehicles, light duty trucks, sport utility vehicles, and mini vans equipped with trw seat belt buckle assemblies. the buckle base of these seat belt assemblies were not properly heat treated and therefore do not pass the load bearing requirement of federal motor vehicle safety standard no. 209, "seat belt assemblies."

Corrective Action

in the event of a vehicle crash, the occupant may not be properly restrained.

Recall Notes

dealers will inspect the vehicle's safety belt buckle assembly date codes and, if necessary, will replace any safety belt buckle assembly.

2001 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: minivans equipped with passenger side power sliding doors. the door closes but may not be latched. if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface.

Corrective Action

an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will install a new un-latch actuator assembly to the power sliding door. this recall has been continued under safety recall 01v-264. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

2001 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

on certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a passenger using the interior handle to open the power sliding door could be injured.

Corrective Action

if a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

Recall Notes

dealers will replace the power sliding door interior handle on the passenger-side. if the vehicle is equipped with a power or manual sliding door on the driver-side, the interior handle will also be replaced for appearance reasons. note: before the vehicle is serviced, gm advises owners to not use the interior door handle to open the door. the driver can open and close the door from switches at the driver's position or by using the remote key fob. the driver should tell passengers to use the switch located in front of the door to open or close it. the driver should use the override switch to prevent operation of the power door by children or by others who are not familiar with its use. the owner notification letter mailing will be conducted in phases with the first phase beginning on may 31, 2005. the second phase mailing began on july 18, 2005. the recall began on may 31, 2005. phase 2 began on july 18, 2005. phase 3 (final phase) began on august 24, 2005, to all remaining customers. owners should contact chevrolet at 1-800-630-2438; pontiac at 1-800-620-7668; or oldsmobile at 1-800-630-6537.

2001 Oldsmobile Silhouette

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.

2000 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: 1997-2001 chevrolet venture, pontiac montana/transport, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors that were serviced in campaign 01013 (01v-067) from april to august 2001. also 2001 chevrolet venture, pontiac montana, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors assembled in january through april 2001. these vehicles have inadequate front welds. if a front weld fails, the actuator can jam in the unlatched position and, when the sliding door closes, it will not be latched.

Corrective Action

if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface. an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will inspect and, if required, install a new power sliding door unlatch actuator assembly. owner notification began on october 22, 2001. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

2000 Oldsmobile Silhouette

Component

Seat Belts

Consequence of Defect

vehicle description: passenger vehicles, light duty trucks, sport utility vehicles, and mini vans equipped with trw seat belt buckle assemblies. the buckle base of these seat belt assemblies were not properly heat treated and therefore do not pass the load bearing requirement of federal motor vehicle safety standard no. 209, "seat belt assemblies."

Corrective Action

in the event of a vehicle crash, the occupant may not be properly restrained.

Recall Notes

dealers will inspect the vehicle's safety belt buckle assembly date codes and, if necessary, will replace any safety belt buckle assembly.

2000 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: minivans equipped with passenger side power sliding doors. the door closes but may not be latched. if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface.

Corrective Action

an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will install a new un-latch actuator assembly to the power sliding door. this recall has been continued under safety recall 01v-264. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

2000 Oldsmobile Silhouette

Component

Fuel System, Gasoline:Delivery:Hoses, Lines/Piping, And Fittings

Consequence of Defect

vehicle description: mini vans with extended wheelbase. some of these vehicles have inoperative fuel tank rollover valves and fuel leakage would exceed the permissible amount in a rollover test. this does not comply with the requirements of fmvss no. 301, "fuel system integrity."

Corrective Action

in a vehicle rollover accident, if an ignition source is present, a fire could result.

Recall Notes

dealers will inspect the vehicles to locate and replace those fuel tanks that could have inoperative rollover valves.

2000 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

on certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a passenger using the interior handle to open the power sliding door could be injured.

Corrective Action

if a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

Recall Notes

dealers will replace the power sliding door interior handle on the passenger-side. if the vehicle is equipped with a power or manual sliding door on the driver-side, the interior handle will also be replaced for appearance reasons. note: before the vehicle is serviced, gm advises owners to not use the interior door handle to open the door. the driver can open and close the door from switches at the driver's position or by using the remote key fob. the driver should tell passengers to use the switch located in front of the door to open or close it. the driver should use the override switch to prevent operation of the power door by children or by others who are not familiar with its use. the owner notification letter mailing will be conducted in phases with the first phase beginning on may 31, 2005. the second phase mailing began on july 18, 2005. the recall began on may 31, 2005. phase 2 began on july 18, 2005. phase 3 (final phase) began on august 24, 2005, to all remaining customers. owners should contact chevrolet at 1-800-630-2438; pontiac at 1-800-620-7668; or oldsmobile at 1-800-630-6537.

2000 Oldsmobile Silhouette

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.

1999 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: 1997-2001 chevrolet venture, pontiac montana/transport, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors that were serviced in campaign 01013 (01v-067) from april to august 2001. also 2001 chevrolet venture, pontiac montana, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors assembled in january through april 2001. these vehicles have inadequate front welds. if a front weld fails, the actuator can jam in the unlatched position and, when the sliding door closes, it will not be latched.

Corrective Action

if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface. an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will inspect and, if required, install a new power sliding door unlatch actuator assembly. owner notification began on october 22, 2001. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

1999 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: minivans equipped with passenger side power sliding doors. the door closes but may not be latched. if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface.

Corrective Action

an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will install a new un-latch actuator assembly to the power sliding door. this recall has been continued under safety recall 01v-264. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

1999 Oldsmobile Silhouette

Component

Steering:Gear Box:Shaft Sector

Consequence of Defect

vehicle description: passenger mini vans. the left and/or right front lower insulator to cradle center metal sleeve is collapsed, which can result in loss of clamp load in the joint. if the clamp load is reduced or lost, the bolt can be lost or broken and the joint can separate.

Corrective Action

if not repaired, separation of the opposite side joint could occur resulting in steering shaft separation.

Recall Notes

dealers will replace the left and right front lower cradle-to-suspension insulators and the attaching bolts.

1999 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

on certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a passenger using the interior handle to open the power sliding door could be injured.

Corrective Action

if a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

Recall Notes

dealers will replace the power sliding door interior handle on the passenger-side. if the vehicle is equipped with a power or manual sliding door on the driver-side, the interior handle will also be replaced for appearance reasons. note: before the vehicle is serviced, gm advises owners to not use the interior door handle to open the door. the driver can open and close the door from switches at the driver's position or by using the remote key fob. the driver should tell passengers to use the switch located in front of the door to open or close it. the driver should use the override switch to prevent operation of the power door by children or by others who are not familiar with its use. the owner notification letter mailing will be conducted in phases with the first phase beginning on may 31, 2005. the second phase mailing began on july 18, 2005. the recall began on may 31, 2005. phase 2 began on july 18, 2005. phase 3 (final phase) began on august 24, 2005, to all remaining customers. owners should contact chevrolet at 1-800-630-2438; pontiac at 1-800-620-7668; or oldsmobile at 1-800-630-6537.

1999 Oldsmobile Silhouette

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.

1998 Oldsmobile Silhouette

Component

Power Train:Automatic Transmission

Consequence of Defect

vehicle description: mini vans. these vehicles may have (1) a broken shift cable fitting or (2) loose shift linkage. consequently, moving the shift lever to a 'park' position may not shift the transmission to 'park'.

Corrective Action

the vehicle could roll increasing the risk of a crash.

Recall Notes

dealers will inspect, and replace if necessary, the automatic transaxle range selector cable.

1998 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: 1997-2001 chevrolet venture, pontiac montana/transport, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors that were serviced in campaign 01013 (01v-067) from april to august 2001. also 2001 chevrolet venture, pontiac montana, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors assembled in january through april 2001. these vehicles have inadequate front welds. if a front weld fails, the actuator can jam in the unlatched position and, when the sliding door closes, it will not be latched.

Corrective Action

if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface. an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will inspect and, if required, install a new power sliding door unlatch actuator assembly. owner notification began on october 22, 2001. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

1998 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: minivans equipped with passenger side power sliding doors. the door closes but may not be latched. if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface.

Corrective Action

an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will install a new un-latch actuator assembly to the power sliding door. this recall has been continued under safety recall 01v-264. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

1998 Oldsmobile Silhouette

Component

Seats:Front Assembly:Recliner

Consequence of Defect

vehicle description: passenger mini vans equipped with bucket seats or a split bench seat in the second (middle) or third (back) row. the seat latch mechanisms on bucket seats and on the 40% portion of the split bench seat in the second and third rows do not have protective covers.

Corrective Action

when activating the release mechanism to roll a bucket seat forward, a customer's finger(s) could be severely injured or severed in they are not kept clear of the mechanism.

Recall Notes

dealers will install protective covers on the outboard latch mechanisms on all left and right hand rear bucket seats in the second and third row, and to both inboard and outboard latch mechanisms on the center rear bucket seat and the 40% portion of the split bench seat.

1998 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

on certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a passenger using the interior handle to open the power sliding door could be injured.

Corrective Action

if a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

Recall Notes

dealers will replace the power sliding door interior handle on the passenger-side. if the vehicle is equipped with a power or manual sliding door on the driver-side, the interior handle will also be replaced for appearance reasons. note: before the vehicle is serviced, gm advises owners to not use the interior door handle to open the door. the driver can open and close the door from switches at the driver's position or by using the remote key fob. the driver should tell passengers to use the switch located in front of the door to open or close it. the driver should use the override switch to prevent operation of the power door by children or by others who are not familiar with its use. the owner notification letter mailing will be conducted in phases with the first phase beginning on may 31, 2005. the second phase mailing began on july 18, 2005. the recall began on may 31, 2005. phase 2 began on july 18, 2005. phase 3 (final phase) began on august 24, 2005, to all remaining customers. owners should contact chevrolet at 1-800-630-2438; pontiac at 1-800-620-7668; or oldsmobile at 1-800-630-6537.

1998 Oldsmobile Silhouette

Component

Steering:Rack And Pinion

Consequence of Defect

certain passenger vehicles and mini vans have lower pinion bearings in the power rack and pinion assembly in which the retainer tabs were not crimped properly. these and some other retainers used in vehicles assembled between january 1, 1996 and october 31, 1997, could fail and permit the ball bearings to escape.

Corrective Action

if this occurs, the pinion shaft can be forced upward during left turns and back down as the steering wheel is moved back and to the right. if the pinion shaft moves further, the driver will need to exert more effort to turn the steering wheel, similar to a vehicle without power assisted steering. if the pinion shaft moves even further, the driver will require much higher effort to turn left and may not be able to turn the wheel as much as intended. with the maximum pinion shaft movement, which requires internal gear component damage, the driver can encounter high resistance to turning left, followed by unintended power assist to the right. in any of these conditions, a crash could occur.

Recall Notes

dealers will install a new lower pinion bearing unless inspect of the existing bearing indicates that replacement of the gear assembly is necessary. owner notification began january 24, 2003. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

1998 Oldsmobile Silhouette

Component

Visibility:Windshield Wiper/Washer:Linkages

Consequence of Defect

vehicle description: passenger mini vans equipped with traction control systems. the windshield wiper linkage arm can contact a brake line which is connected to the traction control system modulator valve. this contact can chafe the brake line resulting in a brake fluid leak.

Corrective Action

brake fluid leakage can cause reduced brake effectiveness and increased stopping distances.

Recall Notes

dealers will install a brake line clip to ensure proper clearance. also the brake lines will be inspected to any damage caused by this condition and will replace any damaged lines.

1998 Oldsmobile Silhouette

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.

1997 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: 1997-2001 chevrolet venture, pontiac montana/transport, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors that were serviced in campaign 01013 (01v-067) from april to august 2001. also 2001 chevrolet venture, pontiac montana, and oldsmobile silhouette mini vans equipped with passenger side power sliding doors assembled in january through april 2001. these vehicles have inadequate front welds. if a front weld fails, the actuator can jam in the unlatched position and, when the sliding door closes, it will not be latched.

Corrective Action

if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface. an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will inspect and, if required, install a new power sliding door unlatch actuator assembly. owner notification began on october 22, 2001. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

1997 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

vehicle description: minivans equipped with passenger side power sliding doors. the door closes but may not be latched. if this happens, the power sliding door can open while the vehicle is in motion, particularly when the vehicle ascends a hill, makes a turn, or travels over a rough road surface.

Corrective Action

an unrestrained occupant could fall out of the van and be injured.

Recall Notes

dealers will install a new un-latch actuator assembly to the power sliding door. this recall has been continued under safety recall 01v-264. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

1997 Oldsmobile Silhouette

Component

Seats:Front Assembly:Recliner

Consequence of Defect

vehicle description: passenger mini vans equipped with bucket seats or a split bench seat in the second (middle) or third (back) row. the seat latch mechanisms on bucket seats and on the 40% portion of the split bench seat in the second and third rows do not have protective covers.

Corrective Action

when activating the release mechanism to roll a bucket seat forward, a customer's finger(s) could be severely injured or severed in they are not kept clear of the mechanism.

Recall Notes

dealers will install protective covers on the outboard latch mechanisms on all left and right hand rear bucket seats in the second and third row, and to both inboard and outboard latch mechanisms on the center rear bucket seat and the 40% portion of the split bench seat.

1997 Oldsmobile Silhouette

Component

Latches/Locks/Linkages:Doors:Latch

Consequence of Defect

on certain minivans equipped with second-row bucket seats or captain's chairs and a power sliding door on the passenger side of the vehicle, a passenger using the interior handle to open the power sliding door could be injured.

Corrective Action

if a passenger uses the interior handle to open the power sliding door and holds onto the handle while it is being opened by the motor, the passenger's arm may be pushed into the seat back or armrest and a wrist or lower arm injury may result.

Recall Notes

dealers will replace the power sliding door interior handle on the passenger-side. if the vehicle is equipped with a power or manual sliding door on the driver-side, the interior handle will also be replaced for appearance reasons. note: before the vehicle is serviced, gm advises owners to not use the interior door handle to open the door. the driver can open and close the door from switches at the driver's position or by using the remote key fob. the driver should tell passengers to use the switch located in front of the door to open or close it. the driver should use the override switch to prevent operation of the power door by children or by others who are not familiar with its use. the owner notification letter mailing will be conducted in phases with the first phase beginning on may 31, 2005. the second phase mailing began on july 18, 2005. the recall began on may 31, 2005. phase 2 began on july 18, 2005. phase 3 (final phase) began on august 24, 2005, to all remaining customers. owners should contact chevrolet at 1-800-630-2438; pontiac at 1-800-620-7668; or oldsmobile at 1-800-630-6537.

1997 Oldsmobile Silhouette

Component

Steering:Rack And Pinion

Consequence of Defect

certain passenger vehicles and mini vans have lower pinion bearings in the power rack and pinion assembly in which the retainer tabs were not crimped properly. these and some other retainers used in vehicles assembled between january 1, 1996 and october 31, 1997, could fail and permit the ball bearings to escape.

Corrective Action

if this occurs, the pinion shaft can be forced upward during left turns and back down as the steering wheel is moved back and to the right. if the pinion shaft moves further, the driver will need to exert more effort to turn the steering wheel, similar to a vehicle without power assisted steering. if the pinion shaft moves even further, the driver will require much higher effort to turn left and may not be able to turn the wheel as much as intended. with the maximum pinion shaft movement, which requires internal gear component damage, the driver can encounter high resistance to turning left, followed by unintended power assist to the right. in any of these conditions, a crash could occur.

Recall Notes

dealers will install a new lower pinion bearing unless inspect of the existing bearing indicates that replacement of the gear assembly is necessary. owner notification began january 24, 2003. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

1997 Oldsmobile Silhouette

Component

Visibility:Windshield Wiper/Washer:Linkages

Consequence of Defect

vehicle description: passenger mini vans equipped with traction control systems. the windshield wiper linkage arm can contact a brake line which is connected to the traction control system modulator valve. this contact can chafe the brake line resulting in a brake fluid leak.

Corrective Action

brake fluid leakage can cause reduced brake effectiveness and increased stopping distances.

Recall Notes

dealers will install a brake line clip to ensure proper clearance. also the brake lines will be inspected to any damage caused by this condition and will replace any damaged lines.

1997 Oldsmobile Silhouette

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.

1996 Oldsmobile Silhouette

Component

Steering:Rack And Pinion

Consequence of Defect

certain passenger vehicles and mini vans have lower pinion bearings in the power rack and pinion assembly in which the retainer tabs were not crimped properly. these and some other retainers used in vehicles assembled between january 1, 1996 and october 31, 1997, could fail and permit the ball bearings to escape.

Corrective Action

if this occurs, the pinion shaft can be forced upward during left turns and back down as the steering wheel is moved back and to the right. if the pinion shaft moves further, the driver will need to exert more effort to turn the steering wheel, similar to a vehicle without power assisted steering. if the pinion shaft moves even further, the driver will require much higher effort to turn left and may not be able to turn the wheel as much as intended. with the maximum pinion shaft movement, which requires internal gear component damage, the driver can encounter high resistance to turning left, followed by unintended power assist to the right. in any of these conditions, a crash could occur.

Recall Notes

dealers will install a new lower pinion bearing unless inspect of the existing bearing indicates that replacement of the gear assembly is necessary. owner notification began january 24, 2003. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020, pontiac at 1-800-762-2737, or oldsmobile at 1-800-442-6537.

1996 Oldsmobile Silhouette

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.

1995 Oldsmobile Silhouette

Component

Service Brakes, Hydraulic:Pedals And Linkages

Consequence of Defect

improperly manufactured brake pedal arm causes the brake pedal arm to fracture during braking.

Corrective Action

this condition can result in a loss of brake operation increasing braking distance and the potential for a vehicle accident.

Recall Notes

dealers will replace all suspect brake pedal assemblies.

1995 Oldsmobile Silhouette

Component

Power Train:Automatic Transmission:Cooling Unit And Lines

Consequence of Defect

vehicle description: passenger vehicles manufactured from august 1991 through july 1995. the transmission oil cooler line can separate when the vehicle is operated in low temperatures in combination with high transmission loads.

Corrective Action

vehicle fires can occur due to the spillage of transmission fluid.

Recall Notes

dealers will replace the transmission oil cooler lines.

1994 Oldsmobile Silhouette

Component

Seat Belts:Front:Webbing

Consequence of Defect

the second row, right hand shoulder belt can become "pinched" between the seat and the door frame pillar trim. the shoulder belt may not retract properly, which does not comply with the requirements of fmvss no. 208, "occupant crash protection." the 1994 vehicles have an optional integral (built in) childseat installed next to the power sliding side door. the 1993 involved vehicles have standard seats in that same position.

Corrective Action

improper shoulder belt retraction does not provide adequate protection to the seat occupant in the event of a sudden stop or collision.

Recall Notes

dealers will replace the door frame pillar trim panel with a redesigned trim panel. also, a caution label will be applied to the child seat advising the owner not to install the seat to the passenger side of a vehicle with a power sliding side door.

1994 Oldsmobile Silhouette

Component

Seat Belts:Rear

Consequence of Defect

the safety belt retractors for the rear center position are missing a pawl spring and in case of an accident, will allow the safety belt webbing to extend beyond the minimum requirements of fmvss no. 208, "occupant crash protection."

Corrective Action

in the event of an accident the safety belt would notrestrain the occupant, subjecting the occupant to increased risk of injuries.

Recall Notes

dealers will inspect the safety belt retractor assembly and replace the retractor if the pawl spring is missing.

1994 Oldsmobile Silhouette

Component

Seat Belts:Front:Retractor

Consequence of Defect

the third row safety belt retractors may be installed incorrectly and may lock-up when the vehicle is on slopes of less than 15 degrees, which does not comply with fmvss no. 209, "seat belt assemblies."

Corrective Action

consequence of non-compliance: passengers seated in these positon maybe unable to extract and fasten their seat belts until the vehicle is moved to a more level surface. unbelted occupants are more at risk of injury in the event of a collision than those using safety belts.

Recall Notes

dealers will remove third row safety belt retractors and reinstall them properly.

1994 Oldsmobile Silhouette

Component

Power Train:Automatic Transmission:Cooling Unit And Lines

Consequence of Defect

vehicle description: passenger vehicles manufactured from august 1991 through july 1995. the transmission oil cooler line can separate when the vehicle is operated in low temperatures in combination with high transmission loads.

Corrective Action

vehicle fires can occur due to the spillage of transmission fluid.

Recall Notes

dealers will replace the transmission oil cooler lines.

1993 Oldsmobile Silhouette

Component

Seat Belts:Front:Webbing

Consequence of Defect

the second row, right hand shoulder belt can become "pinched" between the seat and the door frame pillar trim. the shoulder belt may not retract properly, which does not comply with the requirements of fmvss no. 208, "occupant crash protection." the 1994 vehicles have an optional integral (built in) childseat installed next to the power sliding side door. the 1993 involved vehicles have standard seats in that same position.

Corrective Action

improper shoulder belt retraction does not provide adequate protection to the seat occupant in the event of a sudden stop or collision.

Recall Notes

dealers will replace the door frame pillar trim panel with a redesigned trim panel. also, a caution label will be applied to the child seat advising the owner not to install the seat to the passenger side of a vehicle with a power sliding side door.

1993 Oldsmobile Silhouette

Component

Seat Belts:Rear

Consequence of Defect

vehicle fails to conform to fmvss no. 209, "seat belt assemblies." the safety belt of the left third row seat on the six passenger van and the center second row seat of the seven passenger van may lock up and cannot be withdrawn from the retractor.

Corrective Action

consequence of non-compliance: the occupants of these seats will not be able to use the affected belt. in the event of a vehicle crash, unbelted occupants are at increased risk of injury.

Recall Notes

owners are being asked to inspect their vehicles to determine if the suspect retractor exhibits a lockup condition. based on this inspection, dealers will replace the safety belts if the belt locks up. replacement of the suspect safety belt will be available to consumers for the life of the vehicle.

1993 Oldsmobile Silhouette

Component

Power Train:Automatic Transmission:Cooling Unit And Lines

Consequence of Defect

vehicle description: passenger vehicles manufactured from august 1991 through july 1995. the transmission oil cooler line can separate when the vehicle is operated in low temperatures in combination with high transmission loads.

Corrective Action

vehicle fires can occur due to the spillage of transmission fluid.

Recall Notes

dealers will replace the transmission oil cooler lines.

1992 Oldsmobile Silhouette

Component

Seat Belts:Rear

Consequence of Defect

vehicle fails to conform to fmvss no. 209, "seat belt assemblies." the safety belt of the left third row seat on the six passenger van and the center second row seat of the seven passenger van may lock up and cannot be withdrawn from the retractor.

Corrective Action

consequence of non-compliance: the occupants of these seats will not be able to use the affected belt. in the event of a vehicle crash, unbelted occupants are at increased risk of injury.

Recall Notes

owners are being asked to inspect their vehicles to determine if the suspect retractor exhibits a lockup condition. based on this inspection, dealers will replace the safety belts if the belt locks up. replacement of the suspect safety belt will be available to consumers for the life of the vehicle.

1992 Oldsmobile Silhouette

Component

Power Train:Automatic Transmission:Cooling Unit And Lines

Consequence of Defect

vehicle description: passenger vehicles manufactured from august 1991 through july 1995. the transmission oil cooler line can separate when the vehicle is operated in low temperatures in combination with high transmission loads.

Corrective Action

vehicle fires can occur due to the spillage of transmission fluid.

Recall Notes

dealers will replace the transmission oil cooler lines.

1991 Oldsmobile Silhouette

Component

Seats

Consequence of Defect

this is not a safety recall in accordance with the safety act. however, it is deemed a safety improvement campaign by the agency. vehicle description: minivans equipped with front bucket seats. the front seat recliner mechanism lower bolts can loosen. a loose bolt could fatigue and break, resulting in the seat back falling rearward.

Corrective Action

the seat could suddenly fall backward, distracting the driver, increasing the risk of a crash.

Recall Notes

dealers will tighten or replace the bolts at no charge to the owners. this policy is in effect until june 30, 2002.

1991 Oldsmobile Silhouette

Component

Structure:Body

Consequence of Defect

the glove compartment door will not remain closed during certain load forces associated with a vehicle crash. this does not comply with the requirements of fmvss 201.

Corrective Action

in the event of an accident, the glove compartment doormay open and result in occupant(s) injuries from contact with the glovecompartment door.

Recall Notes

replace the current upper glove compartment door with a redesigned upper glove compartment door which incorporates a positive latch to keep the door closed should a vehicle crash occur.

1991 Oldsmobile Silhouette

Component

Structure

Consequence of Defect

vehicle description: passenger vehicles and mini vans originally sold or currently registered in the following states: connecticut, illinois, indiana, maine, massachusetts, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont and wisconsin. the rear cradle bolts pull through the retainers due to corrosion of the retainer. if both bolts pull through, the rear cradle would not longer be supported at these mounting locations and the steering intermediate shaft can separate from the steering gear.

Corrective Action

if this were to occur while the vehicle was in motion, a vehicle crash could result.

Recall Notes

dealers will replace the rear cradle bolts and retainers.

1990 Oldsmobile Silhouette

Component

Seats

Consequence of Defect

the rear modular seat frame hold-down hooks may not meet the required pull force at the rear set anchorage.

Corrective Action

vehicles would not conform to fmvss 207.

Recall Notes

replace rear hold down hooks and pivot rivets with heat treated hardware.

1990 Oldsmobile Silhouette

Component

Seats

Consequence of Defect

this is not a safety recall in accordance with the safety act. however, it is deemed a safety improvement campaign by the agency. vehicle description: minivans equipped with front bucket seats. the front seat recliner mechanism lower bolts can loosen. a loose bolt could fatigue and break, resulting in the seat back falling rearward.

Corrective Action

the seat could suddenly fall backward, distracting the driver, increasing the risk of a crash.

Recall Notes

dealers will tighten or replace the bolts at no charge to the owners. this policy is in effect until june 30, 2002.

1990 Oldsmobile Silhouette

Component

Structure:Body

Consequence of Defect

the glove compartment door will not remain closed during certain load forces associated with a vehicle crash. this does not comply with the requirements of fmvss 201.

Corrective Action

in the event of an accident, the glove compartment doormay open and result in occupant(s) injuries from contact with the glovecompartment door.

Recall Notes

replace the current upper glove compartment door with a redesigned upper glove compartment door which incorporates a positive latch to keep the door closed should a vehicle crash occur.

1990 Oldsmobile Silhouette

Component

Structure

Consequence of Defect

vehicle description: passenger vehicles and mini vans originally sold or currently registered in the following states: connecticut, illinois, indiana, maine, massachusetts, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont and wisconsin. the rear cradle bolts pull through the retainers due to corrosion of the retainer. if both bolts pull through, the rear cradle would not longer be supported at these mounting locations and the steering intermediate shaft can separate from the steering gear.

Corrective Action

if this were to occur while the vehicle was in motion, a vehicle crash could result.

Recall Notes

dealers will replace the rear cradle bolts and retainers.

1990 Oldsmobile Silhouette

Component

Seat Belts:Front:Anchorage

Consequence of Defect

a right hand seat/shoulder belt retractor may have been installed in the second row left hand seat position (directly behind driver).

Corrective Action

the incorrect retractor may cause the belts to lock upif the van is parked on a steep grade. as a result of this, the occupant couldnot extend the belt for use.

Recall Notes

replace shoulder belt assembly.