Lemon Law Center

United States
Europe
Japan
Korea
RV
Tires

Home > Oldsmobile

1999 Oldsmobile Cutlass

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.


1998 Oldsmobile Cutlass

Component

Steering:Rack And Pinion

Consequence of Defect

certain passenger vehicles have lower pinion bearings in the power rack and pinion assembly in which the retainer tabs were not crimped properly. these retainers could fail and permit the ball bearings to escape.

Corrective Action

if this occurs, the pinion shaft can be forced upward during left turns and back down as the steering wheel is moved back and to the right. if the pinion shaft moves further, the driver will need to exert more effort to turn the steering wheel, similar to a vehicle without power assisted steering. if the pinion shaft moves even further, the driver will require much higher effort to turn left and may not be able to turn the wheel as much as intended. with the maximum pinion shaft movement, which requires internal gear component damage, the driver can encounter high resistance to turning left, followed by unintended power assist to the right. in any of these conditions, a crash could occur.

Recall Notes

dealers will install a new lower pinion bearing unless inspect of the existing bearing indicates that replacement of the gear assembly is necessary. owner notification began on february 5, 2004. owners should contact buick at 1-866-608-8080; chevrolet at 1-800-630-2438; oldsmobile at 1-800-630-6537; or pontiac at 1-800-620-7668.


1998 Oldsmobile Cutlass

Component

Visibility:Windshield Wiper/Washer:Linkages

Consequence of Defect

on certain passenger vehicles originally sold in or currently registered in the "salt belt" states: alaska, colorado, connecticut, delaware, idaho, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, montana, nebraska, new hampshire, new jersey, new york, north dakota, ohio, pennsylvania, rhode island, south dakota, utah, vermont, west virginia, wisconsin, and wyoming. if a buildup of snow or ice restricts the movement of the passenger side windshield wiper arm, the pivot housing can crack and the wipers will not operate.

Corrective Action

reduced visibility in inclement weather could lead to a vehicle crash.

Recall Notes

dealers will replace the passenger side windshield wiper pivot housing. owner notification began august 14, 2001. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020 or oldsmobile at 1-800-442-6537.


1998 Oldsmobile Cutlass

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.


1997 Oldsmobile Cutlass

Component

Steering:Rack And Pinion

Consequence of Defect

certain passenger vehicles have lower pinion bearings in the power rack and pinion assembly in which the retainer tabs were not crimped properly. these retainers could fail and permit the ball bearings to escape.

Corrective Action

if this occurs, the pinion shaft can be forced upward during left turns and back down as the steering wheel is moved back and to the right. if the pinion shaft moves further, the driver will need to exert more effort to turn the steering wheel, similar to a vehicle without power assisted steering. if the pinion shaft moves even further, the driver will require much higher effort to turn left and may not be able to turn the wheel as much as intended. with the maximum pinion shaft movement, which requires internal gear component damage, the driver can encounter high resistance to turning left, followed by unintended power assist to the right. in any of these conditions, a crash could occur.

Recall Notes

dealers will install a new lower pinion bearing unless inspect of the existing bearing indicates that replacement of the gear assembly is necessary. owner notification began on february 5, 2004. owners should contact buick at 1-866-608-8080; chevrolet at 1-800-630-2438; oldsmobile at 1-800-630-6537; or pontiac at 1-800-620-7668.


1997 Oldsmobile Cutlass

Component

Visibility:Windshield Wiper/Washer:Linkages

Consequence of Defect

on certain passenger vehicles originally sold in or currently registered in the "salt belt" states: alaska, colorado, connecticut, delaware, idaho, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, montana, nebraska, new hampshire, new jersey, new york, north dakota, ohio, pennsylvania, rhode island, south dakota, utah, vermont, west virginia, wisconsin, and wyoming. if a buildup of snow or ice restricts the movement of the passenger side windshield wiper arm, the pivot housing can crack and the wipers will not operate.

Corrective Action

reduced visibility in inclement weather could lead to a vehicle crash.

Recall Notes

dealers will replace the passenger side windshield wiper pivot housing. owner notification began august 14, 2001. owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact chevrolet at 1-800-222-1020 or oldsmobile at 1-800-442-6537.


1997 Oldsmobile Cutlass

Component

Fuel System, Other:Storage:Tank Assembly:Pressure Relief Devices

Consequence of Defect

certain delphi fuel pressure regulators, p/nos. fp10020-11b1, fp10026-11b1, and fp10027-11b1, sold after january 9, 2007, as aftermarket equipment for various passenger vehicles listed above. the universal pressure regulators (upr) were produced without an o'ring and retainer.

Corrective Action

fuel may leak, possibly resulting in a fire.

Recall Notes

delphi will notify owners and replace the upr free of charge. the recall began on april 23, 2007. owners can contact delphi at 877-411-8770.


1995 Oldsmobile Cutlass

Component

Seat Belts:Front:Anchorage

Consequence of Defect

the center rear seat belt anchor plate exhibits stress cracks.

Corrective Action

in the event of a vehicle crash, the seat belt system can fracture, increasing the risk of injury to the seat occupant.

Recall Notes

dealers will replace the center rear seat belt system.


1995 Oldsmobile Cutlass

Component

Seat Belts:Front:Anchorage

Consequence of Defect

the center rear seat belt anchor plate exhibits stress cracks.

Corrective Action

in the event of a vehicle crash, the seat belt system can fracture and injury to the seat occupant can occur.

Recall Notes

dealers will replace the center rear seat belt system.


1995 Oldsmobile Cutlass

Component

Visibility:Windshield Wiper/Washer:Switch/Wiring

Consequence of Defect

some of these vehicles have a strained or separated washer/wiper switch power feed wire.

Corrective Action

this can cause the windshield washer/wiper to work intermittently and could ultimately result in inoperative wipers. if this were to occur in a severe weather situation, driver visibility could be reduced, increasing the risk of a vehicle crash.

Recall Notes

dealers will inspect and replace the old designed washer/wiper switches with a newly designed switch.


1994 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Foundation Components:Hoses, Lines/Piping, And Fittings

Consequence of Defect

the brake lines can contact the transmission mounting bracket of the frame side rail. the lines can wear through resulting in loss of brake fluid, and eventual loss of half the vehicle braking system.

Corrective Action

a leak in the hydraulic brake line will cause a loss of one half the vehicle braking system and extended braking distances which can result in an accident.

Recall Notes

dealers will inspect for proper brake line clearance and reposition the brake lines. brake lines found to have indentations will be replaced.


1994 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Foundation Components:Hoses, Lines/Piping, And Fittings

Consequence of Defect

the rear wheel brake hose(s) can contact the rear suspension components causing the brake hose(s) to wear through.

Corrective Action

this condition can cause loss of brake fluid and eventual loss of the vehicle braking system increasing the potential for a vehicle accident.

Recall Notes

dealers will inspect for proper brake hose position and replace those hoses in an incorrect position with new hoses and correctly routed.


1994 Oldsmobile Cutlass

Component

Visibility:Windshield Wiper/Washer:Switch/Wiring

Consequence of Defect

some of these vehicles have a strained or separated washer/wiper switch power feed wire.

Corrective Action

this can cause the windshield washer/wiper to work intermittently and could ultimately result in inoperative wipers. if this were to occur in a severe weather situation, driver visibility could be reduced, increasing the risk of a vehicle crash.

Recall Notes

dealers will inspect and replace the old designed washer/wiper switches with a newly designed switch.


1994 Oldsmobile Cutlass

Component

Vehicle Speed Control

Consequence of Defect

the cruise control cable may separate from the conduit end fitting while engaged and accelerator control could be lost.

Corrective Action

loss of accelerator control may not reduce engine speedto a level anticipated by the driver. although the vehicle can still be stoppedwith the service brake, loss of accelerator control could result in a vehiclecrash without prior warning.

Recall Notes

replace the cruise control cable.


1993 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Foundation Components:Hoses, Lines/Piping, And Fittings

Consequence of Defect

the brake lines can contact the transmission mounting bracket of the frame side rail. the lines can wear through resulting in loss of brake fluid, and eventual loss of half the vehicle braking system.

Corrective Action

a leak in the hydraulic brake line will cause a loss of one half the vehicle braking system and extended braking distances which can result in an accident.

Recall Notes

dealers will inspect for proper brake line clearance and reposition the brake lines. brake lines found to have indentations will be replaced.


1993 Oldsmobile Cutlass

Component

Seats

Consequence of Defect

the driver and passenger front seat manual reclining mechanisms do not comply with the requirements of fmvss 207, "seating systems." the seat back mechanisms will not latch under certain conditions.

Corrective Action

the seats may recline without prior warning, resultingin a hazard to seat occupants and possible loss of vehicle control.

Recall Notes

replace the manual seat recliner mechanism with a mechanism that complies with fmvss 207.


1992 Oldsmobile Cutlass

Component

Power Train:Automatic Transmission

Consequence of Defect

the reverse servo apply pin may bind in the case which could cause reverse band distress (loss or slipping of reverse), reverse band drag in drive range (poor performance -- poor power), or the transmission to remain in reverse while the shift indicator shows neutral gear position.

Corrective Action

if the transmission remains in reverse while the shiftindicator shows neutral, the vehicle may unexpectedly move rearward and resultin a vehicle accident.

Recall Notes

replace the transaxle where required.


1991 Oldsmobile Cutlass

Component

Structure

Consequence of Defect

vehicle description: passenger vehicles and mini vans originally sold or currently registered in the following states: connecticut, illinois, indiana, maine, massachusetts, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont and wisconsin. the rear cradle bolts pull through the retainers due to corrosion of the retainer. if both bolts pull through, the rear cradle would not longer be supported at these mounting locations and the steering intermediate shaft can separate from the steering gear.

Corrective Action

if this were to occur while the vehicle was in motion, a vehicle crash could result.

Recall Notes

dealers will replace the rear cradle bolts and retainers.


1991 Oldsmobile Cutlass

Component

Seat Belts

Consequence of Defect

the front door shoulder belt guide loops may be cracked and are not in compliance with fmvss 208.

Corrective Action

the seat occupant faces increased risk of injury in theevent of a sudden stop or accident.

Recall Notes

install reinforcing plates on the cracked shoulder belt guides.


1990 Oldsmobile Cutlass

Component

Exterior Lighting:Brake Lights:Switch

Consequence of Defect

brake stoplamps may not illuminate or, in some cases, stoplamps will not stay illuminated all the time when brakes are applied due to a faulty stoplamp switch. also in vehicles equipped with cruise control, a faulty stoplamp switch can result in resumption of the cruise control function upon release of the brake pedal.

Corrective Action

a trailing vehicle may not recognize a braking actionin time to respond appropriately. also, cruise control will reengage uponrelease of the brake pedal and resume the set speed. in either case, it couldresult in a crash without prior warning.

Recall Notes

install an improved design stoplamp switch.


1990 Oldsmobile Cutlass

Component

Structure

Consequence of Defect

vehicle description: passenger vehicles and mini vans originally sold or currently registered in the following states: connecticut, illinois, indiana, maine, massachusetts, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont and wisconsin. the rear cradle bolts pull through the retainers due to corrosion of the retainer. if both bolts pull through, the rear cradle would not longer be supported at these mounting locations and the steering intermediate shaft can separate from the steering gear.

Corrective Action

if this were to occur while the vehicle was in motion, a vehicle crash could result.

Recall Notes

dealers will replace the rear cradle bolts and retainers.


1990 Oldsmobile Cutlass

Component

Seat Belts

Consequence of Defect

front shoulder safety belt webbing may separate at front belt upper guide loops on either side of the front seat.

Corrective Action

webbing separation could occur without prior warning andincrease the risk of injury to belted front outboard occupants in a high energycrash.

Recall Notes

install a controlled rotation bracket on driver and passenger side front seat belt guide loops.


1990 Oldsmobile Cutlass

Component

Wheels

Consequence of Defect

cracks develop in the wheel mounting surface. if these cracks become severe enough, the wheel will completely separate from the vehicle.

Corrective Action

if wheel separation occurs while the vehicle is in motion, loss of steering and brake control of the vehicle occurs, and a vehicle crash could result without prior warning.

Recall Notes

dealers will inspect the manufacturing date codes stamped on each wheel of the vehicle and if a wheel falls within the specified date code range, the dealer will replace that wheel assembly.


1990 Oldsmobile Cutlass

Component

Wheels

Consequence of Defect

cracks develop in the wheel mounting surface. if these cracks become severe enough, the wheel will completely separate from the vehicle.

Corrective Action

if wheel separation occurs while the vehicle is in motion, loss of steering and brake control of the vehicle occurs, and a vehicle crash could result without prior warning.

Recall Notes

dealers will inspect the manufacturing codes stamped on each wheel of the vehicle and if a wheel falls within the specified date code range, the dealer will replace that wheel assembly.


1990 Oldsmobile Cutlass

Component

Seat Belts

Consequence of Defect

front shoulder belt guide loop attachment fastener may pull through door mounted anchor plate.

Corrective Action

seat belt may not sustain loads required by fmvss 210, and in a vehicle accident, the seat belt may not properly restrain a passenger, resulting in increased risk of greater injury to an occupant.

Recall Notes

replace front shoulder belt guide loop attachment nuts and install new guide cover.


1989 Oldsmobile Cutlass

Component

Exterior Lighting:Brake Lights:Switch

Consequence of Defect

brake stoplamps may not illuminate or, in some cases, stoplamps will not stay illuminated all the time when brakes are applied due to a faulty stoplamp switch. also in vehicles equipped with cruise control, a faulty stoplamp switch can result in resumption of the cruise control function upon release of the brake pedal.

Corrective Action

a trailing vehicle may not recognize a braking actionin time to respond appropriately. also, cruise control will reengage uponrelease of the brake pedal and resume the set speed. in either case, it couldresult in a crash without prior warning.

Recall Notes

install an improved design stoplamp switch.


1989 Oldsmobile Cutlass

Component

Equipment:Electrical:Air Conditioner

Consequence of Defect

the electronic air conditioning control may not function when starting car that has been parked for a few hours with ignition off.

Corrective Action

windshield may not defrost and car would not conformwith fmvss 103.

Recall Notes

replace electronic comfort control assembly.


1989 Oldsmobile Cutlass

Component

Structure

Consequence of Defect

vehicle description: passenger vehicles and mini vans originally sold or currently registered in the following states: connecticut, illinois, indiana, maine, massachusetts, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont and wisconsin. the rear cradle bolts pull through the retainers due to corrosion of the retainer. if both bolts pull through, the rear cradle would not longer be supported at these mounting locations and the steering intermediate shaft can separate from the steering gear.

Corrective Action

if this were to occur while the vehicle was in motion, a vehicle crash could result.

Recall Notes

dealers will replace the rear cradle bolts and retainers.


1989 Oldsmobile Cutlass

Component

Wheels

Consequence of Defect

cracks develop in the wheel mounting surface. if these cracks become severe enough, the wheel will completely separate from the vehicle.

Corrective Action

if wheel separation occurs while the vehicle is in motion, loss of steering and brake control of the vehicle occurs, and a vehicle crash could result without prior warning.

Recall Notes

dealers will inspect the manufacturing date codes stamped on each wheel of the vehicle and if a wheel falls within the specified date code range, the dealer will replace that wheel assembly.


1989 Oldsmobile Cutlass

Component

Wheels

Consequence of Defect

cracks develop in the wheel mounting surface. if these cracks become severe enough, the wheel will completely separate from the vehicle.

Corrective Action

if wheel separation occurs while the vehicle is in motion, loss of steering and brake control of the vehicle occurs, and a vehicle crash could result without prior warning.

Recall Notes

dealers will inspect the manufacturing codes stamped on each wheel of the vehicle and if a wheel falls within the specified date code range, the dealer will replace that wheel assembly.


1989 Oldsmobile Cutlass

Component

Seat Belts

Consequence of Defect

front shoulder belt guide loop attachment fastener may pull through door mounted anchor plate.

Corrective Action

seat belt may not sustain loads required by fmvss 210, and in a vehicle accident, the seat belt may not properly restrain a passenger, resulting in increased risk of greater injury to an occupant.

Recall Notes

replace front shoulder belt guide loop attachment nuts and install new guide cover.


1988 Oldsmobile Cutlass

Component

Parking Brake:Conventional:Mechanical:Linkage And Cable

Consequence of Defect

the parking brake cable may be disconnected from the left rear brake caliper.

Corrective Action

parking brake cannot be properly applied and vehiclewill not meet the grade holding requirements of fmvss 105.

Recall Notes

install a retainer on left rear caliper if cable is not already retained with a cotter pin and adjust parking brake system.


1988 Oldsmobile Cutlass

Component

Structure

Consequence of Defect

vehicle description: passenger vehicles and mini vans originally sold or currently registered in the following states: connecticut, illinois, indiana, maine, massachusetts, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont and wisconsin. the rear cradle bolts pull through the retainers due to corrosion of the retainer. if both bolts pull through, the rear cradle would not longer be supported at these mounting locations and the steering intermediate shaft can separate from the steering gear.

Corrective Action

if this were to occur while the vehicle was in motion, a vehicle crash could result.

Recall Notes

dealers will replace the rear cradle bolts and retainers.


1988 Oldsmobile Cutlass

Component

Vehicle Speed Control

Consequence of Defect

a small nylon bushing in the cruise control servo bail may slip out of place, causing intermittent and unexpected increases in engine speed or dieseling (engine run on with ignition off).

Corrective Action

servo rod assembly could catch on engine components andresult in a stuck throttle with potential for a vehicle crash.

Recall Notes

install a new bushing in cruise control servo bail.


1988 Oldsmobile Cutlass

Component

Wheels

Consequence of Defect

cracks develop in the wheel mounting surface. if these cracks become severe enough, the wheel will completely separate from the vehicle.

Corrective Action

if wheel separation occurs while the vehicle is in motion, loss of steering and brake control of the vehicle occurs, and a vehicle crash could result without prior warning.

Recall Notes

dealers will inspect the manufacturing date codes stamped on each wheel of the vehicle and if a wheel falls within the specified date code range, the dealer will replace that wheel assembly.


1988 Oldsmobile Cutlass

Component

Wheels

Consequence of Defect

cracks develop in the wheel mounting surface. if these cracks become severe enough, the wheel will completely separate from the vehicle.

Corrective Action

if wheel separation occurs while the vehicle is in motion, loss of steering and brake control of the vehicle occurs, and a vehicle crash could result without prior warning.

Recall Notes

dealers will inspect the manufacturing codes stamped on each wheel of the vehicle and if a wheel falls within the specified date code range, the dealer will replace that wheel assembly.


1988 Oldsmobile Cutlass

Component

Seat Belts

Consequence of Defect

front shoulder belt guide loop attachment fastener may pull through door mounted anchor plate.

Corrective Action

seat belt may not sustain loads required by fmvss 210, and in a vehicle accident, the seat belt may not properly restrain a passenger, resulting in increased risk of greater injury to an occupant.

Recall Notes

replace front shoulder belt guide loop attachment nuts and install new guide cover.


1987 Oldsmobile Cutlass

Component

Vehicle Speed Control

Consequence of Defect

a small nylon bushing in the cruise control servo bail may slip out of place, causing intermittent and unexpected increases in engine speed or dieseling (engine run on with ignition off).

Corrective Action

servo rod assembly could catch on engine components andresult in a stuck throttle with potential for a vehicle crash.

Recall Notes

install a new bushing in cruise control servo bail.


1987 Oldsmobile Cutlass

Component

Power Train:Automatic Transmission:Lever And Linkage:Column Shift

Consequence of Defect

manual valve link in the transmission may have been improperly formed.

Corrective Action

the valve link could separate resulting in a gearselection different from what the driver selects. also, car could be startedwith transmission in gear allowing vehicle to move in an unanticipateddirection.

Recall Notes

replace the manual valve detent lever link.


1986 Oldsmobile Cutlass

Component

Vehicle Speed Control

Consequence of Defect

a small nylon bushing in the cruise control servo bail may slip out of place, causing intermittent and unexpected increases in engine speed or dieseling (engine run on with ignition off).

Corrective Action

servo rod assembly could catch on engine components andresult in a stuck throttle with potential for a vehicle crash.

Recall Notes

install a new bushing in cruise control servo bail.


1986 Oldsmobile Cutlass

Component

Seat Belts:Front:Anchorage

Consequence of Defect

left handed driver's side shoulder belt anchor plate may be upside down in lock pillar so that the unthreaded slot of the plate aligned with the hole in the lock pillar. this resulted in the anchor bolt being driven into the slot instead of the threaded hole of the anchor plate. consequence of defect: in a vehicle crash, belt anchor bolt may pull loose from anchor plate, thus failing to comply with fmvss 210, seat belt assembly anchorages, and increases likelihood of injury to occupant.

Corrective Action

Recall Notes

install a bolt anchor plate reinforcement and new bolt, as necessary.


1986 Oldsmobile Cutlass

Component

Electrical System:Wiring: Rear Compartment/Trunk

Consequence of Defect

an incorrectly indexed wiring harness may cause the center high mounted stop lamp to remain illuminated when the headlights or parking lamps are on. fmvss 108 lamps, reflective devices and associated equipment requires that this stop lamp be lighted only when the brakes are applied. also, the opera lamps may come on when the brakes are applied. consequence of defect: the center high mounted stop lamp provides additional warning that the vehicle is slowing or stopping. if this lamp malfunctions, it may contribute to a rear end accident.

Corrective Action

Recall Notes

correctly index wiring harness terminals.


1985 Oldsmobile Cutlass

Component

Seat Belts:Front:Retractor

Consequence of Defect

the vehicles were assembled with front seat belt retractors which may not perform adequately during a collision.

Corrective Action

Recall Notes

the dealer will replace the left and right front seat belt retractors free of charge.


1985 Oldsmobile Cutlass

Component

Steering:Linkages:Tie Rod Assembly

Consequence of Defect

the tie rods are part of the steering linkage and transmit turning movements to the wheels. the bolts that fasten the tie rods to their adjusters may not be tight enough. this could allow the tie rod to loosen and detach itself from the adjuster.

Corrective Action

Recall Notes

the tie rod end bolts will be tightened without cost to the owner.


1985 Oldsmobile Cutlass

Component

Vehicle Speed Control

Consequence of Defect

a small nylon bushing in the cruise control servo bail may slip out of place, causing intermittent and unexpected increases in engine speed or dieseling (engine run on with ignition off).

Corrective Action

servo rod assembly could catch on engine components andresult in a stuck throttle with potential for a vehicle crash.

Recall Notes

install a new bushing in cruise control servo bail.


1984 Oldsmobile Cutlass

Component

Vehicle Speed Control

Consequence of Defect

a small nylon bushing in the cruise control servo bail may slip out of place, causing intermittent and unexpected increases in engine speed or dieseling (engine run on with ignition off).

Corrective Action

servo rod assembly could catch on engine components andresult in a stuck throttle with potential for a vehicle crash.

Recall Notes

install a new bushing in cruise control servo bail.


1984 Oldsmobile Cutlass

Component

Seats:Front Assembly:Recliner

Consequence of Defect

some vehicles have bucket seat back locks that do not conform to federal motor vehicle safety standard 207, anchorage of seats. in event of a crash, the seat back lock may not function.

Corrective Action

Recall Notes

inspection of seat back locks will be performed. locks that have bent, broken or missing hooks will be replaced.


1983 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Foundation Components:Differential Proportional Valve

Consequence of Defect

the brake proportioner valves may break and separate from the master cylinder. this would allow brake fluid to leak and would result in a partial loss of the brake system.

Corrective Action

Recall Notes

the dealer will inspect and, if necessary, replace all suspect valves.


1983 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Foundation Components:Hoses, Lines/Piping, And Fittings

Consequence of Defect

the master cylinder rear brake pipe, which carries brake fluid to the rear brakes, may develop a leak due to extended chafing on the air cleaner resonator bracket.

Corrective Action

Recall Notes

if upon inspection the dealer finds that there is inadequate clearance, the pipe will be reformed to obtain the necessary three quarter inch space. only those pipes showing signs of wear will be replaced.


1982 Oldsmobile Cutlass

Component

Fuel System, Gasoline:Storage:Tank Assembly:Filler Pipe And Cap

Consequence of Defect

under certaain conditions, the hose clamps on the fuel tank filler pipe and fuel tank filler vent pipe could fracture. the fracture of these clamps could cause fuel leakage at any of the four pipe to hose connections. leakage can occur during refueling, or while driving, if the fuel tank is above 3/4 full.

Corrective Action

Recall Notes

dealer will inspect and replace the hose clamps on the fuel tank filler pipe and vent pipe at no cost to owner.


1982 Oldsmobile Cutlass

Component

Fuel System, Gasoline:Fuel Injection System

Consequence of Defect

under certain vehicle operating conditions, the governor weight retainer in the injection pump may fail. the throttle valve could stick, preventing return to idle and shut down of the engine by the driver.

Corrective Action

Recall Notes

dealer will replace the governor weight assembly in the injection pump at no cost to owner.


1981 Oldsmobile Cutlass

Component

Wheels:Center Section

Consequence of Defect

"tx" heavy duty wheels may have been manufactured with laminated steel. the wheel disc may fracture and the wheel and tire could partially or completely separate from the vehicle.

Corrective Action

Recall Notes

the defective wheels will be replaced without charge.


1981 Oldsmobile Cutlass

Component

Suspension:Rear

Consequence of Defect

the bolts that attach the lower rear control arm to the frame may fracture. the rear control arm supports and positions the rear axle. fracture of the bolts would allow the control arm to drop free.

Corrective Action

Recall Notes

both rear control arm attachment bolts will be replaced without charge.


1980 Oldsmobile Cutlass

Component

Suspension:Rear

Consequence of Defect

the bolts that attach the lower rear control arm to the frame may fracture. the rear control arm supports and positions the rear axle. fracture of the bolts would allow the control arm to drop free.

Corrective Action

Recall Notes

both rear control arm attachment bolts will be replaced without charge.


1980 Oldsmobile Cutlass

Component

Visibility:Glass, Side/Rear

Consequence of Defect

the electro-clear rear window defoggers contain a defect which causes the glass to shatter without impact during or some time after use of the defogger. vertical electrical strips may deteriorate and cause hot spots that can result in breakage of the rear glass.

Corrective Action

Recall Notes

vehicles will be inspected for presence of a particular weatherstrip. if present, a layer of a special conductive epoxy will be added to the vertical bar on the rear window glass. this epoxy is a new conductive material which will not react with the weatherstrip.


1980 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Foundation Components:Drum:Wheel Cylinders

Consequence of Defect

excessive enlargement of the wheel cylinder pilot hole in the rear brake backing plate could allow the wheel cylinder to rotate and cause loss of brake fluid. consequence of defect: a loss of brake fluid leads to loss of rear brake action, creating the potential for an accident. front brakes would remain operational.

Corrective Action

Recall Notes

add a part to prevent wheel cylinder from rotating.


1980 Oldsmobile Cutlass

Component

Equipment

Consequence of Defect

certain honeywell fram racing brand hp4 and hp8 oil filters that were manufactured from may 25, 2006, through september 14, 2007, and sold for use as replacement equipment for vehicles list above. the affected filters are marked with a date code a61451 through a72571 sequentially. the date code and part number appear on the filter housing. fram racing hp4 and hp8 oil filters not bearing a date code in this range are not affected by this recall. the gasket of the oil filter becomes more pliable under high temperatures and pressures.

Corrective Action

this condition may cause inadequate sealing and loss of engine oil, possibly resulting in a fire.

Recall Notes

honeywell will replace the affected oil filters free of charge. the recall began during november 2007. owners can contact fram customer service toll-free at 1-800-890-2075.


1980 Oldsmobile Cutlass

Component

Power Train:Axle Assembly:Axle Shaft

Consequence of Defect

rear axle assembly may have axles that were improperly manufactured. this condition may result in separation of the axle shaft and wheel assembly from the vehicle.

Corrective Action

Recall Notes

the dealer will inspect the rear axle to determine whether it was manufactured at the buffalo plant. if so, they will make axle measurements and if necessary replace or modify affected axle components without charge.


1979 Oldsmobile Cutlass

Component

Suspension:Rear

Consequence of Defect

the bolts that attach the lower rear control arm to the frame may fracture. the rear control arm supports and positions the rear axle. fracture of the bolts would allow the control arm to drop free.

Corrective Action

Recall Notes

both rear control arm attachment bolts will be replaced without charge.


1979 Oldsmobile Cutlass

Component

Visibility:Glass, Side/Rear

Consequence of Defect

the electro-clear rear window defoggers contain a defect which causes the glass to shatter without impact during or some time after use of the defogger. vertical electrical strips may deteriorate and cause hot spots that can result in breakage of the rear glass.

Corrective Action

Recall Notes

vehicles will be inspected for presence of a particular weatherstrip. if present, a layer of a special conductive epoxy will be added to the vertical bar on the rear window glass. this epoxy is a new conductive material which will not react with the weatherstrip.


1979 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Foundation Components:Drum:Wheel Cylinders

Consequence of Defect

excessive enlargement of the wheel cylinder pilot hole in the rear brake backing plate could allow the wheel cylinder to rotate and cause loss of brake fluid. consequence of defect: a loss of brake fluid leads to loss of rear brake action, creating the potential for an accident. front brakes would remain operational.

Corrective Action

Recall Notes

add a part to prevent wheel cylinder from rotating.


1979 Oldsmobile Cutlass

Component

Seats:Front Assembly:Head Restraint

Consequence of Defect

the invovled vehicles fail to conform to federal motor vehicle safety standard no. 201, "occupant protection in interior impacts". incorrect head restraints may have been installed.

Corrective Action

Recall Notes

dealer will inspect and, if necessary, install new head restraints at no cost to owner.


1979 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Foundation Components:Disc:Caliper

Consequence of Defect

an incorrect fluid was used as an assembly aid (lubrication) during installation of the piston seal in front brake calipers which were installed in 10.5" x 1" disc brake assemblies used on "a" series cars. the incorrect fluid attacks the piston seal and causes them to swell and deteriorate.

Corrective Action

Recall Notes

dealer will replace the brake caliper piston seals.


1979 Oldsmobile Cutlass

Component

Equipment

Consequence of Defect

certain honeywell fram racing brand hp4 and hp8 oil filters that were manufactured from may 25, 2006, through september 14, 2007, and sold for use as replacement equipment for vehicles list above. the affected filters are marked with a date code a61451 through a72571 sequentially. the date code and part number appear on the filter housing. fram racing hp4 and hp8 oil filters not bearing a date code in this range are not affected by this recall. the gasket of the oil filter becomes more pliable under high temperatures and pressures.

Corrective Action

this condition may cause inadequate sealing and loss of engine oil, possibly resulting in a fire.

Recall Notes

honeywell will replace the affected oil filters free of charge. the recall began during november 2007. owners can contact fram customer service toll-free at 1-800-890-2075.


1979 Oldsmobile Cutlass

Component

Power Train:Axle Assembly:Axle Shaft

Consequence of Defect

rear axle assembly may have axles that were improperly manufactured. this condition may result in separation of the axle shaft and wheel assembly from the vehicle.

Corrective Action

Recall Notes

the dealer will inspect the rear axle to determine whether it was manufactured at the buffalo plant. if so, they will make axle measurements and if necessary replace or modify affected axle components without charge.


1979 Oldsmobile Cutlass

Component

Exterior Lighting:Brake Lights:Switch

Consequence of Defect

on the involved vehicles the brake stoplight and cruise control switch which is operated by the brake pedal may have been assembled with an incorrect lubricant on the actuating plunger. this can cause the rear brake stoplights to become inoperative and the cruise control, if activated, to stay electrically engaged.

Corrective Action

Recall Notes

dealer will inspect and, if necessary, replace the brake stoplight and cruise control switch at no cost to owner.


1978 Oldsmobile Cutlass

Component

Engine And Engine Cooling:Cooling System:Fan

Consequence of Defect

the hub portion of the fan blade assembly could crack due to high stress levels generated during engine operating conditions. eventually, the blade could break apart at the hub and blade pieces could be propelled into the engine. if the hood is open while the engine is running, the fragments would be free to fly from the vehicle.

Corrective Action

Recall Notes

dealer will replace the fan blade assembly without charge to owner.


1978 Oldsmobile Cutlass

Component

Suspension:Front:Wheel Bearing

Consequence of Defect

under certain driving conditions, these vehicles can experience temperatures in the front wheel outer bearing area which can affect the wheel bearing grease. this can result in inadequate lubrication of the bearing. this condition may be further aggravated by improper adjustment of the front wheel spindle nut.

Corrective Action

Recall Notes

the dealer will install new front wheel outer bearings packed with grease and the spindle will be coated with lubricant. new grease retainer caps will also be installed to maintain grease in outer bearing. this will be done free of charge.


1978 Oldsmobile Cutlass

Component

Suspension:Rear

Consequence of Defect

the bolts that attach the lower rear control arm to the frame may fracture. the rear control arm supports and positions the rear axle. fracture of the bolts would allow the control arm to drop free.

Corrective Action

Recall Notes

both rear control arm attachment bolts will be replaced without charge.


1978 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Foundation Components:Drum:Wheel Cylinders

Consequence of Defect

excessive enlargement of the wheel cylinder pilot hole in the rear brake backing plate could allow the wheel cylinder to rotate and cause loss of brake fluid. consequence of defect: a loss of brake fluid leads to loss of rear brake action, creating the potential for an accident. front brakes would remain operational.

Corrective Action

Recall Notes

add a part to prevent wheel cylinder from rotating.


1978 Oldsmobile Cutlass

Component

Equipment

Consequence of Defect

certain honeywell fram racing brand hp4 and hp8 oil filters that were manufactured from may 25, 2006, through september 14, 2007, and sold for use as replacement equipment for vehicles list above. the affected filters are marked with a date code a61451 through a72571 sequentially. the date code and part number appear on the filter housing. fram racing hp4 and hp8 oil filters not bearing a date code in this range are not affected by this recall. the gasket of the oil filter becomes more pliable under high temperatures and pressures.

Corrective Action

this condition may cause inadequate sealing and loss of engine oil, possibly resulting in a fire.

Recall Notes

honeywell will replace the affected oil filters free of charge. the recall began during november 2007. owners can contact fram customer service toll-free at 1-800-890-2075.


1978 Oldsmobile Cutlass

Component

Power Train:Axle Assembly:Axle Shaft

Consequence of Defect

rear axle assembly may have axles that were improperly manufactured. this condition may result in separation of the axle shaft and wheel assembly from the vehicle.

Corrective Action

Recall Notes

the dealer will inspect the rear axle to determine whether it was manufactured at the buffalo plant. if so, they will make axle measurements and if necessary replace or modify affected axle components without charge.


1977 Oldsmobile Cutlass

Component

Power Train:Axle Assembly:Axle Shaft

Consequence of Defect

the rear axle shafts may contain a flaw in the metal. this flaw could allow the shaft to break and the tire and wheel assembly to separate.

Corrective Action

Recall Notes

the dealer will replace one or both rear axle shafts, if necessary, free of charge.


1977 Oldsmobile Cutlass

Component

Steering:Wheel And Handle Bar

Consequence of Defect

Corrective Action

Recall Notes


1976 Oldsmobile Cutlass

Component

Power Train:Automatic Transmission:Gear Position Indication (Prndl)

Consequence of Defect

Corrective Action

Recall Notes


1976 Oldsmobile Cutlass

Component

Equipment

Consequence of Defect

certain honeywell fram racing brand hp4 and hp8 oil filters that were manufactured from may 25, 2006, through september 14, 2007, and sold for use as replacement equipment for vehicles list above. the affected filters are marked with a date code a61451 through a72571 sequentially. the date code and part number appear on the filter housing. fram racing hp4 and hp8 oil filters not bearing a date code in this range are not affected by this recall. the gasket of the oil filter becomes more pliable under high temperatures and pressures.

Corrective Action

this condition may cause inadequate sealing and loss of engine oil, possibly resulting in a fire.

Recall Notes

honeywell will replace the affected oil filters free of charge. the recall began during november 2007. owners can contact fram customer service toll-free at 1-800-890-2075.


1975 Oldsmobile Cutlass

Component

Vehicle Speed Control

Consequence of Defect

Corrective Action

Recall Notes


1975 Oldsmobile Cutlass

Component

Vehicle Speed Control

Consequence of Defect

Corrective Action

Recall Notes


1975 Oldsmobile Cutlass

Component

Power Train:Axle Assembly:Axle Shaft

Consequence of Defect

Corrective Action

Recall Notes


1975 Oldsmobile Cutlass

Component

Equipment

Consequence of Defect

certain honeywell fram racing brand hp4 and hp8 oil filters that were manufactured from may 25, 2006, through september 14, 2007, and sold for use as replacement equipment for vehicles list above. the affected filters are marked with a date code a61451 through a72571 sequentially. the date code and part number appear on the filter housing. fram racing hp4 and hp8 oil filters not bearing a date code in this range are not affected by this recall. the gasket of the oil filter becomes more pliable under high temperatures and pressures.

Corrective Action

this condition may cause inadequate sealing and loss of engine oil, possibly resulting in a fire.

Recall Notes

honeywell will replace the affected oil filters free of charge. the recall began during november 2007. owners can contact fram customer service toll-free at 1-800-890-2075.


1974 Oldsmobile Cutlass

Component

Seat Belts:Front:Retractor

Consequence of Defect

Corrective Action

Recall Notes


1974 Oldsmobile Cutlass

Component

Suspension:Front:Control Arm:Upper Arm

Consequence of Defect

Corrective Action

Recall Notes


1974 Oldsmobile Cutlass

Component

Seats:Front Assembly:Recliner

Consequence of Defect

Corrective Action

Recall Notes


1973 Oldsmobile Cutlass

Component

Service Brakes, Hydraulic:Power Assist:Vacuum

Consequence of Defect

Corrective Action

Recall Notes


1973 Oldsmobile Cutlass

Component

Steering:Linkages

Consequence of Defect

Corrective Action

Recall Notes


1967 Oldsmobile Cutlass

Component

Steering:Wheel And Handle Bar

Consequence of Defect

Corrective Action

Recall Notes